Shipping Process of WEST Cables

WEST Cable Providing free shipping foe cat5e and cat6 on order of $500 & more

WESTCables.com offers Shipping will be free to all our featured products in order of $500 & more. Orders are sent via UPS or USPS dependent upon your order. You'll get Shipping items on the next business day, and Second Day Shipping items in two business days from when you place your order. We ship only to addresses within the United States Mainland also in Canada. 

Thanks for your understanding.  

Comparisons b/w Cat3, Cat5, Cat5e and Cat6 Etehrnet Cables

There are many Improvements of Cat3, Cat5, Cat5e and Cat6 in the passing years, and a little compression b/w the performances and structures of these networking cables.

CAT3 Networking Cables:

In the early 1990′s CAT3 cables were used for house or office wirings. Category 3 cable is known as Cat3. This cable supports the frequency 16MHz and it carries communications data up to 10 Mbit/s. Now it is using the two-line phone. It supported 10Base-T.

CAT5 Networking Cables:    

Category 5 known as Cat 5 cable, Cat5 cable supports the frequency up to 100MHz and it has 4-twisted pair. Cat5 supported 100BASE-T.

It has two varieties:

•      1.    Unshielded Twisted Pair (UTP)
•      2.    Screened Twisted Pair (SCTP)

Screened Twisted Pair (SCTP) type was widely used in the world and which Screened Twisted Pair (SCTP) to provide a measure of extra safety against interference, but it is rarely used outside of Europe.

And I will be explaining about UTP in Cat6 specs.

Cat5e Ethernet Cable:

The specification of category/cat5e improves upon the cat 5.

Category 5e known as Cat 5e cable, it fulfills higher standards of data transmission. Cat5e Ethernet cable supports the frequency up to 350MHz and Cat5e supported 1000BASE-T. It also has 4-twisted pair.

It has two major types:

•          Cat5e Plenum (CMP) cable  
•          Cat5e non-plenum (CMR) cable

CMP stands for Communications Plenum Cable

CMR stands for Communications Riser Cable

     The most common cable in the United States is Plenum because it is low smoke. CMP cable is best for the Installation of Air Conditioning and Ventilating Systems. The plastic jacket of the plenum is fire-retardant. It is used for indoor and also outdoor

      Cat5e non-plenum cable is also known as riser (CMR) cable. This cable is much cheaper against plenum. The plenum is used for indoor and out-door but riser is just used for in-door.

It has two verities:

•      Unshielded Twisted Pair (UTP)
•       Shielded Twisted Pair (STP)

And I will talk about the specs of UTP and STP in cat6 plenum Ethernet cables.

Cat6 Ethernet Cable:

Category 6 is also known as Cat6, and it is the most advanced cable against cat3, cat5, and cat5e and it is the best in performance. A Cat6 cable support 10 Gigabit Ethernet, and it is able to support the frequency up to 550 MHz, it means it fulfills standards of higher data transmission.

It has two major types:

•        Cat5e Plenum (CMP) cable  
•       Cat5e non-plenum (CMR) cable

I have described the specs of Plenum and non-plenum in Cat5e Ethernet Cables.

It also has two verities like cat5e cable:

•        Unshielded Twisted Pair (UTP)
•        Shielded Twisted Pair (STP)

UTP is standards for all categories like cat3, cat5, cat5e and also for cat6. And also it is found in telephone systems. And this cable is most common cable used for networking, UTP is using for video applications and also many cameras providing UTP output.

Shielded Twisted Pair (STP) Cable is introduced by IBM Cabling Systems. This type of cable protects the EMI from exiting and entering the wire and it also protects the neighboring pairs from crosstalk.

Regards
Jason Holder,
43333 Osgood Road Fremont, CA 94539, USA
PH: +1(408) 414-7437
http://www.westcables.com

Use of Networking Cables

Networking cables are often used for connecting one device to some other networking devices which are placed at some distance may be printers or scanners etc. We use them for different purposes.
Network cables are of different types depending upon their networks topology, Protocol, and size. Some people use wireless which somehow decreases the importance of network cables. There are three main types of networking cables which are coaxial wire, Optical Fiber wire, and Twisted Pair cable.
Twisted Pair cable:-In this kind of cables there is pair of wires which are twisted around each other and the purpose of that is to cancel out electromagnetic interference (EMI) of other wire pairs and from other external sources. This cable is often used at home or for some Ethernet networks. There are three different types of the twisted pair of cables which are shielded, unshielded, and foil.
Untwisted pair cable:-It is the opponent of twisted pair cables in twisted cable there is a pair of cable which is twisted around each other but in untwisted pair cable there is a whole different story in this there is also a pair of wire present like in twisted pair wires but they are not twisted to each other they are parallel to each other they move the head to head. They are also used for home purposes but twisted are more often used and these wires are rarely used.
Fiber Cable:-In this of cable there is a center glass core which is surrounded by several layers of protective material. There as an insulating jacket which is made of fire-resistant materials Teflon or PVC.
It is expensive than other cables and it transfers data to longer distances.
Coaxial Cables:- These are often used for the television. It is mainly used to transmit signal.
Networking cables are really a great invention because of them we can transfer our data to different devices placed far. They are really useful in places like hospitals, Educational Centers and mainly in offices. Networking cables are necessary for almost every electrical phenomenon.
We use these cables often in our daily life you can see at home we connect our computer to the modem by using networking cables. It became the necessity of networking thing and it is one of the most important inventions of all time. There are different cables available in the market you can order them by keeping in mind that for which purpose you are using it.
There are three major types of coaxial wires.

1. Rg6 Coaxial wire
2. Rg11 Coaxial wire
3. Rg59 Coaxial wire

But mostly use Rg59 Coaxial wire.

Regards
Jason Holder,
43333 Osgood Road Fremont, CA 94539, USA
PH: +1(408) 414-7437
http://www.westcables.com/

Memory retrieval by near-infrared light

We have always seen that a sudden incident made everyone remember something and also lose a lot of memories. These incidents target specific parts of the brain and bring the difference that either gives rise to new memories or remove the existing ones. Scientists at Hiroshima University (Japan) have built up a close infrared (close IR) laser-enacted procedure for spanning missing connections in a memory stream. The work intends to build comprehension of the systems required in neurotransmission, which could conceivably prompt medications for memory misfortune conditions.

Scientists have been working on the method by which they can bring back the lost memories, they have been working on this process for a very long time now and are still waiting to make a noticeable achievement. While researchers know that incitement of neurotransmitters, for example, glutamate is required for working memory, where and how these synthetic couriers are created remains a puzzle. What is known is that calcium has a basic part to play, as its fixation increments before glutamate discharge—a component that is inadequately comprehended in light of calcium’s trickiness in neuron cells where it exists as a broke down salt, making it hard to control or identify.

A strategy has been created that, when utilized, could permit the generation locales of synthetic errand people inside neurons to be sourced, examined, and even rebooted as required to restore streams amongst neurons and lift memory. The primary period of the strategy includes blended bearer particles that, when connected to the body through splash, diffuse freely into neuron cells, catching and holding set up any calcium they experience by holding positively with it. But since calcium suspended set up is of little use in memory tests unless it can really be distinguished, Abe and his examination group fused chromophores into the bearers to give them light-engrossing properties. At the point when close IR light is anticipated at these altered transporters, they separate by means of two-photon discharge. This breakdown, utilizing light fit for entering tissue without harming it, makes it especially helpful for inward use in living life forms through outer control utilizing lasers. In the lab where the principal investigator was gone ahead, close IR lasers were projected at neuron cells containing the light-sensitive transporters to check whether calcium was discharged. At the point when the electrical charge at every laser-shaft entrance point was recorded, presentation of the electromagnetic wave separated the light-touchy calcium-transporter particles, making them shed their electrically charged calcium cation. As calcium just exists at particular neurotransmitter generation zones in neurons, a higher charge was identified in these focuses. Since this lone occurred in particular territories and at generally abnormal states, it could likewise be derived that the subtle locales of calcium focus in neurons had at last been found.

Researchers can now concentrate on these exact purposes of neurotransmitter creation to create medicines for memory misfortune, regardless of whether by watching how these ranges react to the drug or by acquainting outside sourced glutamate with neurons that are not working.
Read More

Innovation at its Peak: 5 Times Faster than 5G

According to sources, 5G will be in the markets by 2020 but now some researchers were able to build an integrated circuit-based transmitter which will be able to send data much faster than Fiber Optics and this will also beat 5G in terms of speed.

This technology was discussed on the event of “International Solid-State Circuits Conference (ISSCC). A research paper was made for this purpose. The paper talks about a terahertz (THz) transmitter developed by the National Institute of Information and Communications Technology, Panasonic Corporation, and Hiroshima University. This transmitter operates using a frequency range from 290 GHz to 315 GHz and is capable of transmitting digital data at a rate of 105 gigabits per second — which is a communication speed that’s at least 10 times as fast as 5G networks. The transmitter uses a frequency that falls within a currently unallocated range of 275 GHz to 450 GHz. Its use will be covered in the 2019 World Radiocommunication Conference (WRC) under the International Telecommunication Union Radiocommunication Section (ITU-R).

Researchers accomplished the task to meet the speed levels with the help of quadrature amplitude modulation (QAM). The speed exceeded 100gigabits per second. Which is simply unbelievable?
Read More

The New PoE Standard is Introduced

IEEE 802.3bt was the need of this technology because of the increase in the number of Ethernet-connected devices and their need of power.As Power over Ethernet (PoE) continues to grow in popularity, so does the demand for applications with higher power. The current standard, IEEE 802.3at, allows for maximum power at the powered device (PD) of 25.5 W, while the upcoming standard will allow the maximum power of up to 90 W.

What’s New?

This will increase the limit of PoE because it will use all four pairs of the wires which are in it. It will be very useful for pan-tilt-zoom cameras, VoIP Phones, LED Lights and the list is countless.

This not only enables the new higher power level but also provides better efficiency for the current PoE power level. The power loss in the cable is cut in about half. For example, an IEEE 802.3at PSE (power sourcing equipment) is required to supply a minimum of 30 W to ensure that the PD will receive 25.5 W. In the IEEE 802.3at standard, as much as 4.5 W is lost in the CAT5 cable.

Powering the same 25.5 W with the IEEE 802.3bt standard will cut the loss to less than 2.25 W. This increases the power-delivery efficiency from ~85% to ~92%. When you consider the number of PoE-powered devices in the world, this translates to a very large reduction in power, and in many cases up to a 7% lower carbon footprint for areas that are powered by fossil fuel.The new standard will define two more types of PSEs and PDs—Types 3 and 4. These additions will increase the maximum PoE power by delivering more power through two or more pairs of Ethernet cables.A new physical-layer classification, auto class, will help the PSE determine the actual maximum power drawn by the connected PD. Type 3 and 4 PSEs will identify the PD and set the power accordingly to the maximum PD power, resulting in a better power-delivery system.To maintain a PSE power, a PD must generate a power signature while the lights are off and data communication remains active. The new standard will reduce the time duration and the Maintain Power Signature (MPS) duty cycle to reduce the average standby power/current, benefiting applications such as LED lighting due to the high number of ports.The IEEE 802.3at standard required ~0.13 W to be consumed by a PD,” explains Heath. “If the PD fell below this power level, the PSE would turn off power completely. The new IEEE 802.3bt standard allows a much lower power for the standby level. Only ~0.02 W is required to maintain a power connection. This allows PoE to power ‘green’ applications with agency requirements for low standby power.

What about its future?

We all know that innovation always has bright future but when we talk about the reports from MarketsandMarkets, the PoE market is expected to grow and reach more than $1 billion by 2022. The PoE market will expand with the new standard, giving way to higher-power solutions.Technically speaking, the new standard will allow for more power (60 and 90 W sourced), enhanced system efficiency, and better optimization of system power allocation, From a market point of view, the standard opens new markets that were not previously accessible. One example is PoE lighting.There will be an emergence of so-called ‘connected lighting systems,

So, basically it is a remarkable innovation in the field of technology, it’ll help networking improve like never before.

                     ↓ 

For More Information Visit Our Website 

Over Coaxial Adapter: Innovation in the field of Adapters

We all love cables but hate them sometimes as well, why we love them? Because they are very quick and why do we hate them? Because they are wires and get tangled sometimes and sometimes are too much in the amount they are not presentable. Another reason for hating them is that they keep us suspended to a certain place and don’t provide much of the portability. Watching those cables strung around the wall can be annoying at times as well. Sometimes these cables feel like snakes crawling all around if the place is networked.

An  Ethernet Over Coax Adapter has been introduced to the world. This device is going to use the G.hn standard to make the power of local networks increase. If we try to explain it in simple words, because of this in consumers hands they will not have to buy more Ethernet cables or have them installed. They will be using coaxial cables that are already installed in the homes and offices. The concern is that these cables can’t be used to send the videos. The speed, however, is going to be breathtaking as the providers promise it to be 1 GB/s. This specification is going to have Forward Error Correction (FEC) technology, because of which the videos are going to be seamless and video lag is going to be reduced as well. The problem is that this setup is going to be given to the users that already have the coaxial cables installed if they don’t then it destroys the purpose of this device.
Visit Now

Some Internet Solutions

What if my Wi-Fi router is not working? Most people ask this question very often due to their slow internet and annoying speed. At the end of the day, a Wi-Fi router is a device that can have some issues but it`s not a sign to worry about. At times it is very easy to sort out the issue and sometimes it takes lots of efforts. But the first step is always about detecting the problem that is creating an issue for you.

Wi-Fi routers are available in different colors, sizes and technologies and normally the Wi-Fi routers are provided by the internet supplier. Apart from different styles and sizes, all of them share almost same issues. Following are some of the most commonly observed problems in routers and their simple remedies as well. Have a look:

1. Wi-Fi with extreme slow speed:

The most common problem that people observe is the problem of slow internet, internet suddenly loses all speed and becomes steady. The main reason for the problem is the lack of signals from the internet supplier or maybe your device is not able to get the signals. Even in the peak hours, people complaint to have slow internet. Your neighbor’s Wi-Fi can also interrupt your signals as well. To avoid this clash, you can change your channel range or you could turn off your router for some time and then restart it.

2. Gaming can cause connectivity issues:

If you are addicted to games then you may often face an issue in your internet connectivity. Online games are extremely attractive for the addicts. As a result of this, your internet becomes congested and creates problems for you. But as a matter of fact, this is not a big thing to worry about. The simple solution is to arrange a new router for gaming purpose and a separate one should be used for other internet stuff.

3. Overheating of your Router:

Another big issue that people face is the issue of overheating. It is a fact that once people install the router at their place, they stop taking care of the router that leads to the short lifespan of the router. Excessive use of the router can heat it up and can cause issues for you. So the best remedy is to take proper care of your router and avoid excessive use of it. Don’t forget to turn it off after every 2–3 hours.

Concluding the above:

All of the above-mentioned issues are those which are mostly observed and just by taking small precautions you can have a safe and speedy internet connection. Another important thing is to reboot the router time to time, which enhances its efficiency. At the end of the day, it is an equipment and it can have issues with it but most of them can be resolved if you know some of the basics. Last but not the least, you should check your router properly at the time of delivery just to check any damaged part or anything like that.

Learn More

The Specialty of Crossover Cables

Crossover cables are used to connect two Ethernet cables with each other, they were specially created for the host to host situations.

Standard cables have an identical sequence of colored wires on each end. Crossover cables have the first and third wires (counting from left to right) crossed, and the second and sixth wires crossed

A good Ethernet crossover cable will be specially marked to distinguish it from straight through ones. Many are red in color and also feature the name “crossover” stamped on its packaging and wire casing. Crossover cables were commonly used by Information Technology (IT) professionals in the 1990s and 2000s as the popular forms of Ethernet at that time did not support direct cable connections between hosts. Both the original and Fast Ethernet standards were designed to use specific wires for both the transmit and receive signals.

These standards required the two endpoints to communicate through an intermediate device to avoid conflicts from trying to use the same wires for both transmit and receive. A feature of Ethernet called MDI-X provides the necessary auto-detection support to prevent these signal conflicts.

This feature allows the Ethernet interface to automatically determine which signaling convention the device on the other end of the cable expects and negotiates use of the transmit and receive wires accordingly.Note that only one end of a connection needs to support auto-detection for this feature to work.

Most home broadband routers (even older models) incorporated MDI-X support on their Ethernet interfaces. Gigabit Ethernet also adopted MDI-X as a standard. In summary, crossover cables are only needed when connecting two Ethernet client devices where neither is configured for Gigabit Ethernet. Modern Ethernet devices now automatically detect the use of crossover cables and work with them seamlessly. Crossover cables should only be used for direct network connections.

For the reason described above, attempting to connect a computer to an old router or network switch with a crossover cable instead of a normal cable can prevent the link from functioning. These cables can be specially purchased through various electronics outlets. Hobbyists and some IT professionals may prefer to make their own crossover cables instead.

Read More...

Fire test for communication cable is the need of the hour

With the advent of technology, our lifestyle has changed dramatically. We have changed our workplace and living patterns. We are living a much more comfortable life with the technology gadgets but this gadget which have made of life easy also possess the tendency to take our lives. With our new state of the art buildings equipped with new breathtaking technologies, we are more prone to fatal fire outbreaks. Our buildings are webbed with commination cables which can turn into a fire conductor if proper measures are not taken into consideration by the manufacturers.

There are cable producers who are manufacturing communications cable that does not pass fire and life-safety building codes and yet they label it with all the marketing you need on the proper testified cables.

The communication cables are tested in Steiner Tunnel, in which cables are tested by being subjected to fire. A cable earns the plenum rating by passing specific flame-spread and smoke-generation requirements in a Steiner Tunnel. Cables are subjected to a tunnel and fire is then initiated at one end and then technicians measure how far does the fire reach in the cable.
First fire onset is measured by the control cable whose manufacture is known to be proper and safe and then a cable without UL approved holograph label was subjected to fire which burnt rapidly and produced dense smoke. So when you are installing the cables in your building make sure you are using the right UL approved cables which are designed to withstand fire outbreaks.
Read More